Shattl Premium

Liquid water-emulsion latex coating with the use of polymer microspheres of the new generation, up to 40 microns in size. Provides heat-insulating, hydrophobic and light (heat) reflective properties to various surfaces. The SHUTTLE PREMIUM coating is capable of reducing heat loss on various materials by up to 50% and has no direct analogues among similar systems in Ukraine, being the most innovative product on the market of liquid thermal insulation.

The coating is intended primarily for thermal insulation, as well as partial waterproofing of buildings and structures of residential, industrial and communal use. Has a sanitary certificate and 100% environmental safety. Non-combustible and does not support combustion! It is used for external and internal surfaces. It also has a reflective effect, in which the covered surfaces do not heat up to high temperatures in the hot summer season. In winter, on the contrary, cold bridges are blocked, both on external and internal surfaces, as a result of which the surfaces cease to condense and conduct cold into the room.

SHUTTLE also prevents the spread of mold on various materials and surfaces. Has good adhesion to all known building and construction materials. The possibility of application to the surface of any geometric shape, durability and small thickness are the undeniable advantages of the SHUTTLE coating over traditional heat-insulating materials.

Liquid latex water-based coating using conditionally ceramic microspheres up to 80 microns in size. Reduces heat loss on various surfaces up to 25%. It is used primarily for additional thermal insulation and blocking of cold bridges of various mineral surfaces. It is used in construction, including the finishing of buildings and structures, as well as at various industrial facilities. It has hydrophobic and partially waterproofing properties.

The coating has good adhesion to metal surfaces, concrete, brick, drywall, chipboard, fiberboard, plaster, glass and some types of plastic. When used in residential areas, it prevents the formation of condensate and fungal formations on walls and other surfaces, providing a drying effect. It can be used as thermal insulation of metal pipelines (both hot and cold water supply), steam pipelines, ventilation systems. It also has the properties of reflecting incident light rays and scattering infrared radiation, which contribute to the excellent preservation of heat in rooms when used on internal walls and surfaces, as well as the protection of roofing materials from solar radiation and excessive heating.

The coating has good frost resistance up to -60C, which allows it to be used as thermal insulation and waterproofing of freezers, while reducing labor costs for the construction of a thermal insulation layer of foam boards and a waterproofing layer of roofing felt and foil.

Liquid (thick) latex-based water-based coating with the use of conditionally ceramic microspheres and Moissanite crystals of increased heat resistance. It has high heat resistance, up to 500 0C. Reduces heat loss by up to 25% on various surfaces.

The coating is mainly used for thermal insulation of hot metal surfaces of pipelines, furnaces, chimneys, as well as boiler and industrial equipment with heating temperatures from 200 to 500 0C.

Color from dark gray to black.

Premium Standard Thermo

Colour:

Light gray, with the possibility of tinting

Heat resistance:

250°

Liters

1l./3l./10l.

Download Instructions for Use ( Standard ) Download

Colour:

Dark gray

Heat resistance:

500°

Liters

1l./3l./10l.

Download Instructions for Use ( Thermo ) Download

Colour:

Colour white, with accurate tinting system according to RAL and cis.

Heat resistance:

180°

Liters

1l./3l./10l.

Download Instructions for Use ( Premium ) Download

Coating properties

Thermal insulation

Provides reduction of heat losses on various surfaces up to 50%. It can serve as additional and main insulation.

Thermal insulation

Provides reduction of heat losses on various surfaces up to 30%. It can serve as additional and main insulation.

Thermal insulation

Provides reduction of heat losses on various surfaces up to 30%. It is used as a thermal barrier for high-temperature metal surfaces, chimneys, exhaust systems and industrial equipment with high temperatures from +200 to +500 C. It has a unique heat resistance and the ability of double thermal reflection from the surface of crystals and microspheres.

Heat mirror

Heat mirror It reflects heat radiation. In summer, up to 95% of solar radiation reflected in the outdoors, in winter up to 50% of the thermal radiation reflected inside the room.

Soundproofing

Reduces noise in an isolated room.

Hydrophoby

1.8% water absorption, surface absorption coefficient (kg / m2h) that is not more than 0,001 It is moisture and thus is not a vapor barrier ("breathing" wall). It creates the effect of drying the walls, in which the "dew point" is always to be on the outer surface.

Anticorrosi

It prevents corrosion of the metal, since it does not transmit moisture.

Anti-fungal coating

It does not allow the development of mildew and destroys existing mycelium.

The durability of the coating

Manufacturer's warranty of 10 years!

Ease of work

Application by brush, roller, spatula, spray

Adhesion

Adhesion to almost all construction materials and structures.

Use as a finish

Use as a topcoat with tinting according to the RAL system.

Applications

Industrial and Civil Engineering

Walls, foundation, basement, floors, roofs of residential and industrial buildings and structures; Warming and gidrobarer joints in prefabricated buildings; Metal sheds, garages, warehouses, crane girders; Bridges, tunnels (ensures waterproofing, significantly reduces freezing and corrosion);

Boiler equipment and ventilation systems. Pipelines

КBoilers, pipes and water heating systems, valves, (prevention of heat in the summer, the absence of condensation in the dew point); Gas pipes, steam pipes, heat exchangers; Air ducts, ventilation systems.

Chemical and petrochemical industry

Oil pipelines, gas pipelines; Tanks, storage tanks and transportation of petroleum products, quick-flammable liquids, chemicals (decrease heating, evaporation, increasing the filling).

Transport and Shipbuilding

Coverage of bodies, heads of vehicles, refrigerated trucks, tanks, containers, w / d cars, buildings sea and river vessels, boats.

Food industry and agriculture

Stationary cold storage and mixing tanks; Farm animals; Elevators.

Specifications

Thermal conductivity (W / m ° K), at least

0.002

The heat transfer coefficient of the outer surface (W / m2 ° K)

1.5

Drying time at 20 ° C, an hour at least

Operating temperature range, °С

- 60° +150°

Tensile strength, kg / cm2

Elongation at break,%, not less

1.2

Viscosity, g/cm3

0.7-1.5

Mass fraction of solids, %

40-70

Water absorption of coatings for 24 hours,% by weight

up to 15

Water vapor permeability coating mg/(m*year*Pa), not more

0.02

Frost, zamorazhivanie- thawing at temperatures -60°С +240°С

300 cycles

Adhesion, MPa, no less:

- to metal (steel)

- to concrete

- to wood

0.6

0.8

1.0

Thermal conductivity (W / m ° K), at least

0.01

The heat transfer coefficient of the outer surface (W / m2 ° K)

1.0

Drying time at 20 ° C, an hour at least

Operating temperature range, °С

- 60° +260°

Tensile strength, kg / cm2

Elongation at break,%, not less

1.2

Viscosity, g/cm3

0.7-1.5

Mass fraction of solids, %

40-70

Water absorption of coatings for 24 hours,% by weight

up to 15

Water vapor permeability coating mg/(m*year*Pa), not more

0.02

Frost, zamorazhivanie- thawing at temperatures -60°С +250°С

300 cycles

Adhesion, MPa, no less:

- to metal (steel)

- to concrete

- to wood

0.6

0.8

1.0

Thermal conductivity (W / m ° K), at least

0.01

The heat transfer coefficient of the outer surface (W / m2 ° K)

1.0

Drying time at 20 ° C, an hour at least

Operating temperature range, °С

- 60° +500°

Tensile strength, kg / cm2

Elongation at break,%, not less

1.2

Viscosity, g/cm3

0.7-1.5

Mass fraction of solids, %

40-70

Water absorption of coatings for 24 hours,% by weight

up to 15

Water vapor permeability coating mg/(m*year*Pa), not more

0.02

Frost, zamorazhivanie- thawing at temperatures -60°С +500°С

300 cycles

Adhesion, MPa, no less:

- to metal (steel)

- to concrete

- to wood

0.6

0.8

1.0

Comparison table of thermal conductivity performance:

Material

Coefficient of thermal conductivity

Thickness

Silicate brick

0,8

35 cm

20 cm

Clay brick

0,5

25 cm

14 cm

Foam (or laminated wooden beams)

0,2

15 cm

8 cm

Mineral wool (basalt)

0,05

5 cm

2,5 cm

Expanded polystyrene PSB-25

0,03

3 cm

1,5 cm

SHATTL PREMIUM

SHATTL STANDARD

SHATTL THERMO

0,0025

0,009

2 mm

Calculation tables

Application Instructions

Technological instructions for applying liquid composite insulation coating "SHUTTLE" on concrete, brick, plaster, metal and other surfaces

Coating

Before applying to the surface, "SHUTTLE" mixed until smooth. Stirring means done by hand, mechanically or by means of a mixer (an electric drill with paddle). Peremeschivanie should be implemented at low speed, for 3-5 minutes until smooth. If necessary, the viscosity reducing agent is diluted with water. Add water to be consistent, in small portions, 1% by weight of dye (but not more than 5.7% of the total weight of the agent). "SHUTTLE" can be applied by airless spray high-pressure units with a nozzle diameter of at least 2 mm, roller or brush. It is recommended to use "CEILING" brush (wide flat brush with dense bristles). The coating should be applied to cross-layers (one along the other transverse or vice versa). The drying each layer - at least 20 minutes at a temperature (20 ± 2) ° C. Duration interlayer drying at other temperatures determined on the curing degree. When you touch on the cover should not be a trace. Apply the product must be at ambient temperature not lower than 5 ° C and relative humidity above 80%. To achieve the "Shuttle" covering essential characteristics recommend to apply the coating layer in an amount of not less than 3!

Metal surfaces

In the preparation of metal surfaces, be painted, should be guided by the requirements of SNIP 3.04.03 and GOST 9.402. Metal surfaces should be thoroughly cleaned and primed, it is desirable that a special primer for rust. In the case of application to the stainless surface treat 10% caustic solution (100 g per 1 liter of soda water). On the metal surface becomes hot recommended application from 7 to 10 layers to the overall coating layer was in the range of 1.5-3 mm for better thermal insulation. At the same generic fiber polymerization occurs within two days after application and only then you can start heating surfaces. Over time, the surface color can darken or change due to thermal effects of high temperatures on the latex that does not affect the coating characteristics.

Concrete. Brick. Plaster. A rock.

Before applying the funds to concrete, brick, stone, plaster surfaces, they must be free from all kinds of dirt, dried and filled, for example ST17 primed or her peers. 4-5 applied in layers, depending on the requirements of the object. It is not allowed the presence of moisture or condensation on surfaces to be painted.

Quality control work

Quality control works on application of insulating coatings on concrete, brick, plastered surfaces is carried out at each operation. Subject to the quality control of surface preparation prior to coating as well as coating quality and thickness of insulating coatings. The quality of surface preparation prior to application of funds is checked visually by a check for dirt and lack not primed areas. Acceptance of the prepared surface to draw up an act of covert work. Quality insulating coating after drying is controlled visually. In this case check: no cracks, no blistering, delamination and fraying, no unprotected areas of surfaces.